From 9a11791bf3a48a3a7e54ebd225f179d708184cc5 Mon Sep 17 00:00:00 2001 From: Gnieark Date: Wed, 14 Oct 2015 09:50:25 +0200 Subject: [PATCH] ajout des fichiers de conf du firmware --- Firmware/Configuration.h | 707 +++++++++++++++++++++++++++++++++++ Firmware/Configuration_adv.h | 515 +++++++++++++++++++++++++ Firmware/README.md | 6 + 3 files changed, 1228 insertions(+) create mode 100644 Firmware/Configuration.h create mode 100644 Firmware/Configuration_adv.h create mode 100644 Firmware/README.md diff --git a/Firmware/Configuration.h b/Firmware/Configuration.h new file mode 100644 index 0000000..6c530e9 --- /dev/null +++ b/Firmware/Configuration.h @@ -0,0 +1,707 @@ +#ifndef CONFIGURATION_H +#define CONFIGURATION_H + +#include "boards.h" + +// This configuration file contains the basic settings. +// Advanced settings can be found in Configuration_adv.h +// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer replace the configuration files with the files in the +// example_configurations/delta directory. +// + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time +#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. + +// SERIAL_PORT selects which serial port should be used for communication with the host. +// This allows the connection of wireless adapters (for instance) to non-default port pins. +// Serial port 0 is still used by the Arduino bootloader regardless of this setting. +#define SERIAL_PORT 0 + +// This determines the communication speed of the printer +#define BAUDRATE 250000 + +// This enables the serial port associated to the Bluetooth interface +//#define BTENABLED // Enable BT interface on AT90USB devices + +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_RAMPS_13_EFB +#endif + +// Define this to set a custom name for your generic Mendel, +// #define CUSTOM_MENDEL_NAME "This Mendel" + +// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) +// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// This defines the number of extruders +#define EXTRUDERS 1 + +//// The following define selects which power supply you have. Please choose the one that matches your setup +// 1 = ATX +// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) + +#define POWER_SUPPLY 1 + +// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. +// #define PS_DEFAULT_OFF + +//=========================================================================== +//============================== Delta Settings ============================= +//=========================================================================== +// Enable DELTA kinematics and most of the default configuration for Deltas +#define DELTA + +// Make delta curves from many straight lines (linear interpolation). +// This is a trade-off between visible corners (not enough segments) +// and processor overload (too many expensive sqrt calls). +#define DELTA_SEGMENTS_PER_SECOND 200 + +// NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them + +// Center-to-center distance of the holes in the diagonal push rods. +#define DELTA_DIAGONAL_ROD 250.0 // mm + +// Horizontal offset from middle of printer to smooth rod center. +#define DELTA_SMOOTH_ROD_OFFSET 175.0 // mm + +// Horizontal offset of the universal joints on the end effector. +#define DELTA_EFFECTOR_OFFSET 33.0 // mm + +// Horizontal offset of the universal joints on the carriages. +#define DELTA_CARRIAGE_OFFSET 18.0 // mm + +// Effective horizontal distance bridged by diagonal push rods. +#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET) + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== +// +//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table +// +//// Temperature sensor settings: +// -2 is thermocouple with MAX6675 (only for sensor 0) +// -1 is thermocouple with AD595 +// 0 is not used +// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) +// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) +// 3 is Mendel-parts thermistor (4.7k pullup) +// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! +// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) +// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) +// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) +// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) +// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) +// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) +// 10 is 100k RS thermistor 198-961 (4.7k pullup) +// 11 is 100k beta 3950 1% thermistor (4.7k pullup) +// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) +// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" +// 20 is the PT100 circuit found in the Ultimainboard V2.x +// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 +// +// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k +// (but gives greater accuracy and more stable PID) +// 51 is 100k thermistor - EPCOS (1k pullup) +// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) +// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) +// +// 1047 is Pt1000 with 4k7 pullup +// 1010 is Pt1000 with 1k pullup (non standard) +// 147 is Pt100 with 4k7 pullup +// 110 is Pt100 with 1k pullup (non standard) + +#define TEMP_SENSOR_0 -1 +#define TEMP_SENSOR_1 -1 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_BED 0 + +// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +// Actual temperature must be close to target for this long before M109 returns success +#define TEMP_RESIDENCY_TIME 10 // (seconds) +#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// The minimal temperature defines the temperature below which the heater will not be enabled It is used +// to check that the wiring to the thermistor is not broken. +// Otherwise this would lead to the heater being powered on all the time. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define BED_MINTEMP 5 + +// When temperature exceeds max temp, your heater will be switched off. +// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! +// You should use MINTEMP for thermistor short/failure protection. +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define BED_MAXTEMP 150 + +// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the +// average current. The value should be an integer and the heat bed will be turned on for 1 interval of +// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. +//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 + +// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS +//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R + +// PID settings: +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX 255 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#ifdef PIDTEMP + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + #define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term + #define K1 0.95 //smoothing factor within the PID + #define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine + +// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it +// Ultimaker + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 + +// MakerGear +// #define DEFAULT_Kp 7.0 +// #define DEFAULT_Ki 0.1 +// #define DEFAULT_Kd 12 + +// Mendel Parts V9 on 12V +// #define DEFAULT_Kp 63.0 +// #define DEFAULT_Ki 2.25 +// #define DEFAULT_Kd 440 +#endif // PIDTEMP + +// Bed Temperature Control +// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis +// +// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. +// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz, +// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. +// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. +// If your configuration is significantly different than this and you don't understand the issues involved, you probably +// shouldn't use bed PID until someone else verifies your hardware works. +// If this is enabled, find your own PID constants below. +//#define PIDTEMPBED +// +//#define BED_LIMIT_SWITCHING + +// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. +// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) +// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, +// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#ifdef PIDTEMPBED +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from pidautotune +// #define DEFAULT_bedKp 97.1 +// #define DEFAULT_bedKi 1.41 +// #define DEFAULT_bedKd 1675.16 + +// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + + + +//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit +//can be software-disabled for whatever purposes by +#define PREVENT_DANGEROUS_EXTRUDE +//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately. +#define PREVENT_LENGTHY_EXTRUDE + +#define EXTRUDE_MINTEMP 170 +#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. + +/*================== Thermal Runaway Protection ============================== +This is a feature to protect your printer from burn up in flames if it has +a thermistor coming off place (this happened to a friend of mine recently and +motivated me writing this feature). + +The issue: If a thermistor come off, it will read a lower temperature than actual. +The system will turn the heater on forever, burning up the filament and anything +else around. + +After the temperature reaches the target for the first time, this feature will +start measuring for how long the current temperature stays below the target +minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). + +If it stays longer than _PERIOD, it means the thermistor temperature +cannot catch up with the target, so something *may be* wrong. Then, to be on the +safe side, the system will he halt. + +Bear in mind the count down will just start AFTER the first time the +thermistor temperature is over the target, so you will have no problem if +your extruder heater takes 2 minutes to hit the target on heating. + +*/ +// If you want to enable this feature for all your extruder heaters, +// uncomment the 2 defines below: + +// Parameters for all extruder heaters +//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds +//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius + +// If you want to enable this feature for your bed heater, +// uncomment the 2 defines below: + +// Parameters for the bed heater +//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds +//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius +//=========================================================================== + + +//=========================================================================== +//=============================Mechanical Settings=========================== +//=========================================================================== + +// coarse Endstop Settings +#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors + +#ifndef ENDSTOPPULLUPS + // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined + // #define ENDSTOPPULLUP_XMAX + // #define ENDSTOPPULLUP_YMAX + // #define ENDSTOPPULLUP_ZMAX + // #define ENDSTOPPULLUP_XMIN + // #define ENDSTOPPULLUP_YMIN + // #define ENDSTOPPULLUP_ZMIN +#endif + +#ifdef ENDSTOPPULLUPS + #define ENDSTOPPULLUP_XMAX + #define ENDSTOPPULLUP_YMAX + #define ENDSTOPPULLUP_ZMAX + #define ENDSTOPPULLUP_XMIN + #define ENDSTOPPULLUP_YMIN + #define ENDSTOPPULLUP_ZMIN +#endif + +// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins. +const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +//#define DISABLE_MAX_ENDSTOPS +// Deltas never have min endstops +#define DISABLE_MIN_ENDSTOPS +// Disable max endstops for compatibility with endstop checking routine +#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS) + #define DISABLE_MAX_ENDSTOPS +#endif + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis when it's not being used. +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled + +#define INVERT_X_DIR false // DELTA does not invert +#define INVERT_Y_DIR false +#define INVERT_Z_DIR false + +#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false +#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false +#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false + +// ENDSTOP SETTINGS: +// Sets direction of endstops when homing; 1=MAX, -1=MIN +// deltas always home to max +#define X_HOME_DIR 1 +#define Y_HOME_DIR 1 +#define Z_HOME_DIR 1 + +#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS. +#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. + +// Travel limits after homing +#define X_MAX_POS 90 +#define X_MIN_POS -90 +#define Y_MAX_POS 90 +#define Y_MIN_POS -90 +#define Z_MAX_POS MANUAL_Z_HOME_POS +#define Z_MIN_POS 0 + +#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS) +#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS) +#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS) +//============================= Bed Auto Leveling =========================== +//Bed Auto Leveling is still not compatible with Delta Kinematics + + + + +// The position of the homing switches +//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used +//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0) + +//Manual homing switch locations: + +#define MANUAL_HOME_POSITIONS // MANUAL_*_HOME_POS below will be used +// For deltabots this means top and center of the Cartesian print volume. +#define MANUAL_X_HOME_POS 0 +#define MANUAL_Y_HOME_POS 0 +#define MANUAL_Z_HOME_POS 250 // For delta: Distance between nozzle and print surface after homing. + +//// MOVEMENT SETTINGS +#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E + +// delta homing speeds must be the same on xyz +#define HOMING_FEEDRATE {200*60, 200*60, 200*60, 0} // set the homing speeds (mm/min) + +// default settings +// delta speeds must be the same on xyz +#define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 80, 760*1.1} // default steps per unit for Kossel (GT2, 20 tooth) +#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 25} // (mm/sec) +#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. + +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis + +// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) +#define DEFAULT_XYJERK 20.0 // (mm/sec) +#define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta +#define DEFAULT_EJERK 5.0 // (mm/sec) + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// Custom M code points +#define CUSTOM_M_CODES +#ifdef CUSTOM_M_CODES + #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851 + #define Z_PROBE_OFFSET_RANGE_MIN -15 + #define Z_PROBE_OFFSET_RANGE_MAX -5 +#endif + + +// EEPROM +// The microcontroller can store settings in the EEPROM, e.g. max velocity... +// M500 - stores parameters in EEPROM +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +//define this to enable EEPROM support +//#define EEPROM_SETTINGS +//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: +// please keep turned on if you can. +//#define EEPROM_CHITCHAT + +// Preheat Constants +#define PLA_PREHEAT_HOTEND_TEMP 180 +#define PLA_PREHEAT_HPB_TEMP 70 +#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 + +#define ABS_PREHEAT_HOTEND_TEMP 240 +#define ABS_PREHEAT_HPB_TEMP 100 +#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 + +//LCD and SD support +//#define ULTRA_LCD //general LCD support, also 16x2 +//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) +//#define SDSUPPORT // Enable SD Card Support in Hardware Console +//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication +//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder +//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking +//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. +//#define ULTIPANEL //the UltiPanel as on Thingiverse +//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click + +// The MaKr3d Makr-Panel with graphic controller and SD support +// http://reprap.org/wiki/MaKr3d_MaKrPanel +//#define MAKRPANEL + +// The RepRapDiscount Smart Controller (white PCB) +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// The GADGETS3D G3D LCD/SD Controller (blue PCB) +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +//#define G3D_PANEL + +// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB) +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// The RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click + +// The Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C +//#define RA_CONTROL_PANEL + +// Delta calibration menu +// uncomment to add three points calibration menu option. +// See http://minow.blogspot.com/index.html#4918805519571907051 +// If needed, adjust the X, Y, Z calibration coordinates +// in ultralcd.cpp@lcd_delta_calibrate_menu() +// #define DELTA_CALIBRATION_MENU + +//automatic expansion +#if defined (MAKRPANEL) + #define DOGLCD + #define SDSUPPORT + #define ULTIPANEL + #define NEWPANEL + #define DEFAULT_LCD_CONTRAST 17 +#endif + +#if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define DOGLCD + #define U8GLIB_ST7920 + #define REPRAP_DISCOUNT_SMART_CONTROLLER +#endif + +#if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL) + #define ULTIPANEL + #define NEWPANEL +#endif + +#if defined(REPRAPWORLD_KEYPAD) + #define NEWPANEL + #define ULTIPANEL +#endif +#if defined(RA_CONTROL_PANEL) + #define ULTIPANEL + #define NEWPANEL + #define LCD_I2C_TYPE_PCA8574 + #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander +#endif + +//I2C PANELS + +//#define LCD_I2C_SAINSMART_YWROBOT +#ifdef LCD_I2C_SAINSMART_YWROBOT + // This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home ) + // Make sure it is placed in the Arduino libraries directory. + #define LCD_I2C_TYPE_PCF8575 + #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander + #define NEWPANEL + #define ULTIPANEL +#endif + +// PANELOLU2 LCD with status LEDs, separate encoder and click inputs +//#define LCD_I2C_PANELOLU2 +#ifdef LCD_I2C_PANELOLU2 + // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) + // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. + // (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file) + // Note: The PANELOLU2 encoder click input can either be directly connected to a pin + // (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). + #define LCD_I2C_TYPE_MCP23017 + #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander + #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD + #define NEWPANEL + #define ULTIPANEL + + #ifndef ENCODER_PULSES_PER_STEP + #define ENCODER_PULSES_PER_STEP 4 + #endif + + #ifndef ENCODER_STEPS_PER_MENU_ITEM + #define ENCODER_STEPS_PER_MENU_ITEM 1 + #endif + + + #ifdef LCD_USE_I2C_BUZZER + #define LCD_FEEDBACK_FREQUENCY_HZ 1000 + #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 + #endif + +#endif + +// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs +//#define LCD_I2C_VIKI +#ifdef LCD_I2C_VIKI + // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) + // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. + // Note: The pause/stop/resume LCD button pin should be connected to the Arduino + // BTN_ENC pin (or set BTN_ENC to -1 if not used) + #define LCD_I2C_TYPE_MCP23017 + #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander + #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later) + #define NEWPANEL + #define ULTIPANEL +#endif + +// Shift register panels +// --------------------- +// 2 wire Non-latching LCD SR from: +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection +//#define SR_LCD +#ifdef SR_LCD + #define SR_LCD_2W_NL // Non latching 2 wire shift register + //#define NEWPANEL +#endif + + +#ifdef ULTIPANEL +// #define NEWPANEL //enable this if you have a click-encoder panel + #define SDSUPPORT + #define ULTRA_LCD + #ifdef DOGLCD // Change number of lines to match the DOG graphic display + #define LCD_WIDTH 20 + #define LCD_HEIGHT 5 + #else + #define LCD_WIDTH 20 + #define LCD_HEIGHT 4 + #endif +#else //no panel but just LCD + #ifdef ULTRA_LCD + #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display + #define LCD_WIDTH 20 + #define LCD_HEIGHT 5 + #else + #define LCD_WIDTH 16 + #define LCD_HEIGHT 2 + #endif + #endif +#endif + +// default LCD contrast for dogm-like LCD displays +#ifdef DOGLCD +# ifndef DEFAULT_LCD_CONTRAST +# define DEFAULT_LCD_CONTRAST 32 +# endif +#endif + +// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Temperature status LEDs that display the hotend and bet temperature. +// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on. +// Otherwise the RED led is on. There is 1C hysteresis. +//#define TEMP_STAT_LEDS + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +#define SOFT_PWM_SCALE 0 + +// M240 Triggers a camera by emulating a Canon RC-1 Remote +// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ +// #define PHOTOGRAPH_PIN 23 + +// SF send wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder. +//#define BARICUDA + +//define BlinkM/CyzRgb Support +//#define BLINKM + +/*********************************************************************\ +* R/C SERVO support +* Sponsored by TrinityLabs, Reworked by codexmas +**********************************************************************/ + +// Number of servos +// +// If you select a configuration below, this will receive a default value and does not need to be set manually +// set it manually if you have more servos than extruders and wish to manually control some +// leaving it undefined or defining as 0 will disable the servo subsystem +// If unsure, leave commented / disabled +// +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Servo Endstops +// +// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. +// Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500. +// +//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1 +//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles + +/**********************************************************************\ + * Support for a filament diameter sensor + * Also allows adjustment of diameter at print time (vs at slicing) + * Single extruder only at this point (extruder 0) + * + * Motherboards + * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector + * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 - Rambo - uses Analog input 3 + * Note may require analog pins to be defined for different motherboards + **********************************************************************/ +// Uncomment below to enable +//#define FILAMENT_SENSOR + +#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) +#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm +#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm +#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + +//defines used in the code +#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + +//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. +//#define FILAMENT_LCD_DISPLAY + + + + + + + +#include "Configuration_adv.h" +#include "thermistortables.h" + +#endif //__CONFIGURATION_H diff --git a/Firmware/Configuration_adv.h b/Firmware/Configuration_adv.h new file mode 100644 index 0000000..31787aa --- /dev/null +++ b/Firmware/Configuration_adv.h @@ -0,0 +1,515 @@ +#ifndef CONFIGURATION_ADV_H +#define CONFIGURATION_ADV_H + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +#ifdef BED_LIMIT_SWITCHING + #define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS +#endif +#define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control + +//// Heating sanity check: +// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature +// If the temperature has not increased at the end of that period, the target temperature is set to zero. +// It can be reset with another M104/M109. This check is also only triggered if the target temperature and the current temperature +// differ by at least 2x WATCH_TEMP_INCREASE +//#define WATCH_TEMP_PERIOD 40000 //40 seconds +//#define WATCH_TEMP_INCREASE 10 //Heat up at least 10 degree in 20 seconds + +#ifdef PIDTEMP + // this adds an experimental additional term to the heatingpower, proportional to the extrusion speed. + // if Kc is choosen well, the additional required power due to increased melting should be compensated. + #define PID_ADD_EXTRUSION_RATE + #ifdef PID_ADD_EXTRUSION_RATE + #define DEFAULT_Kc (1) //heatingpower=Kc*(e_speed) + #endif +#endif + + +//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode. +//The maximum buffered steps/sec of the extruder motor are called "se". +//You enter the autotemp mode by a M109 S T F +// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp +// you exit the value by any M109 without F* +// Also, if the temperature is set to a value +// Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results +// as long as it supports dual x-carriages. (M605 S0) +// Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so +// that additional slicer support is not required. (M605 S1) +// Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all +// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at +// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + +// This is the default power-up mode which can be later using M605. +#define DEFAULT_DUAL_X_CARRIAGE_MODE 0 + +// As the x-carriages are independent we can now account for any relative Z offset +#define EXTRUDER1_Z_OFFSET 0.0 // z offset relative to extruder 0 + +// Default settings in "Auto-park Mode" +#define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder +#define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder + +// Default x offset in duplication mode (typically set to half print bed width) +#define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif //DUAL_X_CARRIAGE + +//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again: +#define X_HOME_RETRACT_MM 5 +#define Y_HOME_RETRACT_MM 5 +#define Z_HOME_RETRACT_MM 5 // deltas need the same for all three axis + +//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially. + +#define AXIS_RELATIVE_MODES {false, false, false, false} + +#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step) + +//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +//default stepper release if idle +#define DEFAULT_STEPPER_DEACTIVE_TIME 60 + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +// Feedrates for manual moves along X, Y, Z, E from panel +#ifdef ULTIPANEL +#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min) +#endif + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +// (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) +//#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec) + +// MS1 MS2 Stepper Driver Microstepping mode table +#define MICROSTEP1 LOW,LOW +#define MICROSTEP2 HIGH,LOW +#define MICROSTEP4 LOW,HIGH +#define MICROSTEP8 HIGH,HIGH +#define MICROSTEP16 HIGH,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16] + +// Motor Current setting (Only functional when motor driver current ref pins are connected to a digital trimpot on supported boards) +#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) + +// uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro +//#define DIGIPOT_I2C +// Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8 +#define DIGIPOT_I2C_NUM_CHANNELS 8 +// actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS +#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ +#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again + +#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers? +#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place. + +#define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the filesystem block order. +// if a file is deleted, it frees a block. hence, the order is not purely cronological. To still have auto0.g accessible, there is again the option to do that. +// using: +//#define MENU_ADDAUTOSTART + +// Show a progress bar on the LCD when printing from SD +//#define LCD_PROGRESS_BAR + +#ifdef LCD_PROGRESS_BAR + // Amount of time (ms) to show the bar + #define PROGRESS_BAR_BAR_TIME 2000 + // Amount of time (ms) to show the status message + #define PROGRESS_BAR_MSG_TIME 2000 + // Amount of time (ms) to retain the status message (0=forever) + #define PROGRESS_MSG_EXPIRE 0 + // Enable this to show messages for MSG_TIME then hide them + //#define PROGRESS_MSG_ONCE +#endif + +// The hardware watchdog should reset the Microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation. +//#define USE_WATCHDOG + +#ifdef USE_WATCHDOG +// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. +// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. +// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. +//#define WATCHDOG_RESET_MANUAL +#endif + +// Enable the option to stop SD printing when hitting and endstops, needs to be enabled from the LCD menu when this option is enabled. +//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED + +// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process +// it can e.g. be used to change z-positions in the print startup phase in realtime +// does not respect endstops! +//#define BABYSTEPPING +#ifdef BABYSTEPPING + #define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions + #define BABYSTEP_INVERT_Z false //true for inverse movements in Z + #define BABYSTEP_Z_MULTIPLICATOR 2 //faster z movements + + #ifdef COREXY + #error BABYSTEPPING not implemented for COREXY yet. + #endif + + #ifdef DELTA + #ifdef BABYSTEP_XY + #error BABYSTEPPING only implemented for Z axis on deltabots. + #endif + #endif +#endif + +// extruder advance constant (s2/mm3) +// +// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2 +// +// hooke's law says: force = k * distance +// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant +// so: v ^ 2 is proportional to number of steps we advance the extruder +//#define ADVANCE + +#ifdef ADVANCE + #define EXTRUDER_ADVANCE_K .0 + + #define D_FILAMENT 2.85 + #define STEPS_MM_E 836 + #define EXTRUSION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159) + #define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUSION_AREA) + +#endif // ADVANCE + +// Arc interpretation settings: +#define MM_PER_ARC_SEGMENT 1 +#define N_ARC_CORRECTION 25 + +const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement + +// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted +// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT +// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should +// be commented out otherwise +#define SDCARDDETECTINVERTED + +#ifdef ULTIPANEL + #undef SDCARDDETECTINVERTED +#endif + +// Power Signal Control Definitions +// By default use ATX definition +#ifndef POWER_SUPPLY + #define POWER_SUPPLY 1 +#endif +// 1 = ATX +#if (POWER_SUPPLY == 1) + #define PS_ON_AWAKE LOW + #define PS_ON_ASLEEP HIGH +#endif +// 2 = X-Box 360 203W +#if (POWER_SUPPLY == 2) + #define PS_ON_AWAKE HIGH + #define PS_ON_ASLEEP LOW +#endif + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//=============================Buffers ============================ +//=========================================================================== + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering. +#if defined SDSUPPORT + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + + +//The ASCII buffer for recieving from the serial: +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + + +// Firmware based and LCD controled retract +// M207 and M208 can be used to define parameters for the retraction. +// The retraction can be called by the slicer using G10 and G11 +// until then, intended retractions can be detected by moves that only extrude and the direction. +// the moves are than replaced by the firmware controlled ones. + +// #define FWRETRACT //ONLY PARTIALLY TESTED +#ifdef FWRETRACT + #define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt + #define RETRACT_LENGTH 3 //default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s) + #define RETRACT_ZLIFT 0 //default retract Z-lift + #define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) +#endif + +//adds support for experimental filament exchange support M600; requires display +#ifdef ULTIPANEL + #define FILAMENTCHANGEENABLE + #ifdef FILAMENTCHANGEENABLE + #define FILAMENTCHANGE_XPOS 3 + #define FILAMENTCHANGE_YPOS 3 + #define FILAMENTCHANGE_ZADD 10 + #define FILAMENTCHANGE_FIRSTRETRACT -2 + #define FILAMENTCHANGE_FINALRETRACT -100 + #endif +#endif + +#ifdef FILAMENTCHANGEENABLE + #ifdef EXTRUDER_RUNOUT_PREVENT + #error EXTRUDER_RUNOUT_PREVENT currently incompatible with FILAMENTCHANGE + #endif +#endif + +//=========================================================================== +//============================= Define Defines ============================ +//=========================================================================== + +#if defined (ENABLE_AUTO_BED_LEVELING) && defined (DELTA) + #error "Bed Auto Leveling is still not compatible with Delta Kinematics." +#endif + +#if EXTRUDERS > 1 && defined TEMP_SENSOR_1_AS_REDUNDANT + #error "You cannot use TEMP_SENSOR_1_AS_REDUNDANT if EXTRUDERS > 1" +#endif + +#if EXTRUDERS > 1 && defined HEATERS_PARALLEL + #error "You cannot use HEATERS_PARALLEL if EXTRUDERS > 1" +#endif + +#if TEMP_SENSOR_0 > 0 + #define THERMISTORHEATER_0 TEMP_SENSOR_0 + #define HEATER_0_USES_THERMISTOR +#endif +#if TEMP_SENSOR_1 > 0 + #define THERMISTORHEATER_1 TEMP_SENSOR_1 + #define HEATER_1_USES_THERMISTOR +#endif +#if TEMP_SENSOR_2 > 0 + #define THERMISTORHEATER_2 TEMP_SENSOR_2 + #define HEATER_2_USES_THERMISTOR +#endif +#if TEMP_SENSOR_BED > 0 + #define THERMISTORBED TEMP_SENSOR_BED + #define BED_USES_THERMISTOR +#endif +#if TEMP_SENSOR_0 == -1 + #define HEATER_0_USES_AD595 +#endif +#if TEMP_SENSOR_1 == -1 + #define HEATER_1_USES_AD595 +#endif +#if TEMP_SENSOR_2 == -1 + #define HEATER_2_USES_AD595 +#endif +#if TEMP_SENSOR_BED == -1 + #define BED_USES_AD595 +#endif +#if TEMP_SENSOR_0 == -2 + #define HEATER_0_USES_MAX6675 +#endif +#if TEMP_SENSOR_0 == 0 + #undef HEATER_0_MINTEMP + #undef HEATER_0_MAXTEMP +#endif +#if TEMP_SENSOR_1 == 0 + #undef HEATER_1_MINTEMP + #undef HEATER_1_MAXTEMP +#endif +#if TEMP_SENSOR_2 == 0 + #undef HEATER_2_MINTEMP + #undef HEATER_2_MAXTEMP +#endif +#if TEMP_SENSOR_BED == 0 + #undef BED_MINTEMP + #undef BED_MAXTEMP +#endif + + +#endif //__CONFIGURATION_ADV_H diff --git a/Firmware/README.md b/Firmware/README.md new file mode 100644 index 0000000..ade59f9 --- /dev/null +++ b/Firmware/README.md @@ -0,0 +1,6 @@ +# reprapJeanneV2, Configuration du firmware + +On utilisera Marlin https://github.com/MarlinFirmware/Marlin + +Dans le dépot ReprapJeanneV, je ne mets que les fichiers de configuration. +